Construction Products


Wet and Dry Diamond Core Bits
Wet and Dry Cutting Diamond Saw Blades

Wet and Dry Diamond Core Bits

SOLID BACK STONE GOLD CORE BITS
SBSG (GOLD) are manufactured with the highest quality diamond particles uniformly distributed throughout a special matrix. They are designed specifically to alleviate chipping when drilling through stone or tile.

SEGMENTED CORE BITS
Segmented bits are designed and manufactured with a wide range of bond matrices for fast penetration, and the most economical cost per hole.

SOLID BACK PREMIUM GREEN
SBPG (GREEN) are General Purpose Segmented Bits for use in medium to hard concrete with average reinforcing — high diamond content resulting in excellent footage and cutting speed.

SOLID BACK ECONO-CUT BLACK
SBEB (BLACK) are General Purpose Segmented Bits designed for fast penetration and economical all round drilling applications including free cutting of reinforced concrete.

SOLID BACK RESEGMENTED RED
SBRR (RED) Utilizing Premium Green segments, PARSONS can put a new cutting surface on your used core bit barrel. This diamond bit will provide you with the best cost savings possible.
Resegmented bits utilize only dimensionally sound hubs and barrels.

SOLID BACK DRY BIT
SBDB (SILVER) are Segmented Dry Cutting Bits exclusively for cutting block and soft brick. Available from 1" through 6".



return to top

Wet Cutting Diamond Saw Blades


Masonry Blades
Available in Supreme and Premium
100 Series — For fast smooth cutting of glazed TILE, hard BRICK, and other hard, dense materials.
PD101 — Hard dense non-abrasive brick, brick or dense concrete pavers (5-71/2 HP Saws)
PD105 — Glazed structural tile, brick or dense concrete pavers (1/2-5 HP Saws)
PD115 — dense brick/abrasive brick — Hard-faced
220 Series — Combination Block/BRICK
PD223- For combination: 20% Block/80% BRICK
280 Series — Combination BLOCK/Brick
PD286 - For combination: 80% BLOCK/20% Brick
300 Series — Good Cutting action on medium and lightweight BLOCK
PD306 — Medium aggregate Concrete Block
PD308 — Lightweight aggregate Block
14" x.110x1" Bore
20" x.125x1" Bore
Supreme diamond depth — .375"
Premium diamond depth — .250"

Refractory Blades
Available in Supreme and Premium
410 Series - HARD Refractory
PD411 — For fast cutting of extremely hard, dense refractory material, such as High Alumina (90% and higher),
and non-abrasive acid brick, fused cast, magnesite and zircon.
PD412 — For fast cutting of hard refractory material, such as High Alumina (70% and higher), super duty, and hard basic.
430 Series — MEDIUM Refractory
PD433 — For fast cutting and long life on Medium Hard (50% Alumina) Refractory bricks, ladle brick.
440 Series — SOFT Refractory
PD444 — For Soft Refractory material, such as silica, soft basic chrome and insulating brick.
14" x.110x1"    Bore
18" x .125 x 1" Bore
20" x.125x1"    Bore
Other sizes and specifications available upon request.

Enforcer Masonry
Designed for fast, efficient and economical sawing. ENFORCER DIAMOND BLADES are available for Brick,
Combination Brick & Block, and Lightweight Block.
Available in .187 Diamond Depth Only
14" x .110x 1" Bore 20" x .125 x 1" Bore




Concrete Blades
720 Series —- CURED Concrete
Available in Supreme and Premium
PD721 — Medium/Hard Aggregate - Fast Cutting — General Purpose
PD720 — Medium/Hard Aggregate - Longer Life
PD723 — River Gravel/Flint Aggregate with - Non-Abrasive Sand (Low HP Saws)
PD726 — Hard Aggregate with Steel - Reinforcing for Deep Sawing (High HP Saws) 18" Diameter and Larger.
PD727 — For Cutting Very Hard Cured Concrete with Heavy Duty Steel Reinforcing. For Saws that Use 24" Diameter Blades and Larger.
730 Series — CURED with Asphalt Overlay
Available in Supreme and Premium with Diamond Inserts at No Extra Charge
PD731 — Medium/Hard Aggregate Greater % of Concrete than Asphalt — Fast Cutting
PD730 — Medium/Hard Aggregate Greater % of Concrete than Asphalt — Longer Life
PD732 — Hard Aggregate Greater % of Concrete than Asphalt
PD734 — Soft to Medium Aggregate Greater % of Asphalt than Concrete
800 Series — ASPHALT
Available in Supreme and Premium with Diamond Inserts at No Extra Charge
PD806 — Hard Aggregate — Fast Cutting
PD860 — Hard Aggregate — Longer Life
PD807 — Soft Aggregate with Abrasive Sand - Fast Cutting (General Purpose)
PD870 — Soft Aggregate with Abrasive Sand - Longer Life (High HP Saws)
900 Series — GREEN Concrete
Available in Supreme and Premium with Diamond Inserts at No Extra Charge
PD906 — Medium/Hard Aggregate - Fast Cutting (General Purpose)
PD960 — Medium/Hard Aggregate - Longer Life (High HP Saws)
Other sizes and specifications available upon request.

Small/Large Walk Behind Saw Blades
12" x .110 x 1" Bore with Pin Hole
12" x .125 x 1" Bore with Pin Hole
12" x .187 x 1" Bore with Pin Hole
12" x .250 x 1" Bore with Pin Hole
12" x .312 x 1" Bore with Pin Hole
12" x .375 x 1" Bore with Pin Hole
12" x .500 x 1" Bore with Pin Hole
14" x .110 x 1" Bore with Pin Hole
14" x .125 x 1" Bore with Pin Hole
14" x .187 x 1" Bore with Pin Hole
14" x .250 x 1" Bore with Pin Hole
14" x .312 x 1" Bore with Pin Hole
14" x .375 x 1" Bore with Pin Hole
14" x .500 x 1" Bore with Pin Hole
16" x .125 x 1" Bore with Pin Hole
16" x .145 x 1" Bore with Pin Hole
18" x .125 x 1" Bore with Pin Hole
18" x .145 x 1" Bore with Pin Hole
18" x .187 x 1" Bore with Pin Hole
18" x .250 x 1" Bore with Pin Hole
20" x .125 x 1" Bore with Pin Hole
20" x .145 x 1" Bore with Pin Hole
24" x .145 x 1" Bore with Pin Hole
24" x .175 x 1" Bore with Pin Hole
24" x .187 x 1" Bore with Pin Hole
24" x .250 x 1" Bore with Pin Hole
24" x .375 x 1" Bore with Pin Hole
26" x .175 x 1" Bore with Pin Hole
26" x .187 x 1" Bore with Pin Hole
30" x .187 x 1" Bore with Pin Hole
30" x .218 x 1" Bore with Pin Hole
30" x .250 x 1" Bore with Pin Hole
36" x .187 x 1" Bore with Pin Hole
36" x .218 x 1" Bore with Pin Hole
36" x .250 x 1" Bore with Pin Hole

Depth of Cut

Blade Diameter 12" 14" 16" 18" 20" 24" 26" 30" 36" Cutting
Depth 33A" 4V 5V 6%" 7V 9V 103A" 11%" 14%"

Enforcer Walk Behind Saw Blades
Designed for fast, steady sawing in soft to medium-hard aggregates, ENFORCER DIAMOND BLADES are available for Asphalt, Green, Cured Concrete or Combination. Supplied standard with diamond inserts at no additional charge.
Available in .187 Diamond Depth Only

12" x .110 x 1 Bore with Pin hole
12" x .125 x 1 Bore with Pin hole
14" X .110 x 1 Bore with Pin hole
14" X .125 x 1 Bore with Pin hole
16" X .125 x 1 Bore with Pin hole
18" X .125 x 1 Bore with Pin hole
18" X .187 x 1 Bore with Pin hole
24" X .145 x 1 Bore with Pin hole
24" X .187 x 1 Bore with Pin hole
26" X .175 x 1 Bore with Pin hole
30" X .187 x 1 Bore with Pin hole
36" X .187 x 1 Bore with Pin hole

Continuous Rim
Smooth, continuous rim of diamonds for use on tub saws. For cutting tile, brick, marble, granite, porceline, etc., where no chipping is allowed.

4"   x .060 x 5/8" Bore
5"   x .060 x 5/8" Bore
6"   x .060 x 5/8" Bore
7"   x .060 x 5/8" Bore
8"   x .060 x 5/8" Bore
9"   x .060 x 5/8" Bore
10" x .060 x 5/8" Bore
12" x .080 x 5/8" Bore
14" x .080 x 5/8" Bore

return to top

Dry Cutting Diamond Saw Blades


DRY CUTTING DIAMOND BLADES have been successfully used in a wide variety of applications, and in all types of weather. Operators achieve faster cutting, less dust, reduced costs per cut than conventional abrasive blades, while maintaining a constant depth of cut, safer working conditions, and the virtual elimination of down time. All resulting in less operator fatigue, reduced labor costs, increased productivity and increased PROFITS.

- Specially designed with the highest diamond concentration for longer life when cutting cured concrete, green concrete, asphalt, concrete pavers, and block.
- Highest diamond quality and content for maximum footage and cutting speed.
- Premium quality diamond blades manufactured for your toughest sawing applications including hard concrete with heavy reinforcing, green concrete, asphalt, and brick pavers.
- General purpose quality blades for all around sawing applications of block, common brick, cured concrete, green concrete, and asphalt.
- Designed for cutting extremely hard, dense masonry materials with ease (i.e. ironspot and water-struck brick, concrete and brick pavers, flue pipe). Excellent on such non-abrasive materials as slate, granite, bluestone, and related products.
- Uniquely constructed blades for cutting the widest range of concrete and masonry products (WIDE CURF) and for granite and tile with minimal chipping (THIN CURF).
- Designed for cleaning out mortar joints on brick and block buildings.
- Exceptional on restoration work.

4" x .250 x 7/s"; 20mm; Vs" Bore
41/2" x .250 x Va"; 20mm; 5/8" Bore
5" x .250 x 7/s"; 20mm; Vs" Bore
7" x .250 x DA — Vs" Bore

Single Row — fast removal grinding stone, masonry, concrete, and other similar materials.
Double Row — longer life and smooth finish. Ideal for chamfering, smoothing, and shaping.
4" x 3A" x 7/s"; 20mm; 5/s" Bore
7"x 1"x7/8"; 20mm; 5/s" Bore

Exceptional life for routing random cracks ; on straight-line joints in pavement.
7" x .375 x 5/s" Bore
7" x .500 x Vs" Bore
8" x .375 x 1" Bore
8" x .500 x 1" Bore
Other sizes and specifications available upon request.


Designed for use on hand held saws and angle grinders. These blades make quick work on concrete, brick, tile,
marble, granite, block and pavers.
4" x .085 x 7s"; 20mm; Vs" Bore
41/2" x .085 x Vs"; 20mm; 5/8" Bore
5" x .085 x 7s"; 20mm; 5/a" Bore
6" x .085 x D.A. — 5/s" Bore
7" x .085 x D.A. — Vs" Bore
8" x .085 x D.A. — Vs" Bore
9" x .085 x 22mm; 20mm; 5/s" Bore
10" x .085 x D.A. — Vs" Bore

Intended for use on high speed hand held saws. Ideal for cutting reinforced concrete products including prestressed and precast, concrete pipe or block, lintels, roofing tiles, pavers, slate, granite curbing, or asphalt.
12" x.110x1"; 78M; 20mm
14" x.110x1"; 7s"; 20mm

Uniquely constructed for use on portable and stationary masonry saws cutting materials such as block (concrete and lightweight), brick, flue, concrete and brick pavers, and other related products.
WARNING: For Use on Masonry Saws Only. Do Not Use on high speed or road (flat) saws.
14" x.110x1" Bore
18" x.125x1" Bore
20" x .125 x 1" Bore
Specially formulated for general purpose patch and repair work, trenching, or other intermittent cuts on low HP (11 HP or less) road saws. These blades are designed for cured concrete, or asphalt and green concrete.

ABRASIVE BLADES
FOR MASONRY &
CONCRETE

For Power Hand Saws
7" x Ys" x DA-5/s"; %" (round) Bore
8" x Ys" x DA-5/s"; %" (round) Bore
10" x Ys" x DA-%"; %" (round) Bore
Specification: BR-11—General purpose blade for free hand cutting of most masonry materials, non-ferrous metal, etc.

For High Speed Saws
12" x Vsxl"; 7s"; 20mm
12"x5/32x1";7s"20mm
(BR11-SS only) (6300 RPM) 14" x Vsxl"; 7s"; 20mm
14"x5/32x1";7s"20mm (BR11-SS only) (5400 RPM)
Specifications: BR9-SS—For general purpose masonry and concrete. BR11-SS—For asphalt, or ductile iron with concrete lining.

For Masonry Saws
14" x 1" Bore
Specifications: BR-3 (BRICK), BR-5 (BRICK/BLOCK), BR-7 (BLOCK)— Externally reinforced with two layers of heavy duty fiberglass discs for maximum
safety.

For Small Walk Behind Saws (18 HP or Less)
14" x Vis" x 1" Bore with Pin Hole
Specifications: CC-112 (Concrete) BC-112 (Asphalt)—For general repair work, trench cutting, and industrial maintenance in old and new concrete and in asphalt. Recommended for wet cutting. Double reinforced with heavy fiberglass discs for increased safety.

ABRASIVE BLADES FOR METAL

For Power Hand Saws
7" x 3/32" x DA-5/s"; 5/a(round) Bore
8" x 3/32" x DA-5/s"; 5/s(round) Bore
10" x 3/32" x DA-Vs"; Vs (round) Bore
12" x%2" x 1" Bore 14"x%2"x1"Bore
Specifications: A36S—For stainless steel and general purpose metal cutting. A36S-BF2—For 12" and 14" diameter blades.

For High Speed Saws
12" x Vs x 1"; 7s"; 20mm (6300 RPM)
14" x Vsx 1"; 7/8"; 20mm (5400 RPM)
Specifications: A36S-SS—For general purpose metal cutting. A24Q-SS—For 14" diameter blade.
Reinforced with extra heavy fiberglass discs for maximum safety. See ANSI code B7-1, Sec. 8 covering special speeds concerning machine manufacture and user responsibility.
General
Purpose
A24R-BF1
A30P-BF1

For Cut-Off Saws
16"x5/32"x1"Bore
20" x 5/32" x 1" Bore
BF1 Series—Internally reinforced with single layer of high strength fiberglass discs.





return to top